New products offered by Sea-lect Designs for kayak fishing include an Offset Paddle Holder, Redesigned Anchor Trolley kit, and an Inline Track Mounting option for the Triple Threat Rod Holder!

Sea-lect Designs Offset Paddle Holder

An offset paddle holder is a great addition to any fishing kayak with integrated track mounting. Offsetting the paddle allows the remainder of the track to be utilized instead of being blocked when the paddle is stowed in a normal tack mounted paddle holder. The offset paddle clip mount also includes pre drilled holes to add mounting clamps to stow a stake out pole!

Sea-lect Designs Updated Anchor Trolley System

Also from Sea-lect Designs is an updated anchor trolley system! Incorporating sheaveless pulleys and a new low profile Z-Cleat lock! A Sheaveless pulleys puts the stealth in this anchor trolley system. Without the sound of a wheel this setup is completely silent. Also it doubles as a no maintenance fairly instead of a pulley which can over time fail due to dirt and grime buildup. The new low-profile Z-Cleat is a huge upgrade from the large clam cleat. This lock is flush and can be mounted completely out of your paddle sweep! Another key new feature is the addition of a clip to the ring which allows the anchor trolley to double as a tow rope or a way to clip on while wading!

Sea-lect Designs Triple Threat Track mount

The triple threat through my use and testing is the best lay in rod holder on the market. Reasons being it allows for heavier rods with larger grips to lay in and the 1/4 turn up/dn pivot adjust is key to one handed adjustment. Only thing it is missing is a complete track mount base with adjustable pivot action. From my understanding this is in the works and should be available for 2019! Was not available for display at Icast.

This is not a kit install but a custom anchor trolley.   I wanted it to be unique.

Things you will need

• 2 Pulleys Stainless Steel
• 1/8″ bungee – Color of choice
• at least 30 feet of reflective 5/32″ poly rope
• 2 Deck Loops
• 4 Nuts bolts and rubber washers.
• 2″ Nylon Ring

(Below Not Photoed)

• Galvanized Hog Rings
• Heat Shrink Tubing

Tools

• Drill
• Torch or Bic Lighter
• Pocket Knife
• Philips screw Driver
• 3/8″ Socket
• 1/4″ Drive Socket Wrench
• Pliers

What is an Anchor Trolley and why is it needed?

Access the bow or stern is basically impossible unless you were to get off the kayak and swim there. Simply using a block and loop conveyor system aka Anchor Trolley. An anchor trolley is basically a clothing line that is used to shift the point of your anchoring from cockpit to both bow and stern. An anchor trolley can be installed on either side of the kayak or both. Its all about how you the angler would prefer to use the system.

Now to install your anchor trolley. First you will cut (2) 8″ lengths of the 1/8″ bungee. Use the Torch or Bic lighter to fuse the Nylon sheath around the rubber bungee chords. This will ensure the bungee will not fall apart.

Now you will insert each bungee into the eye of the block and tie both ends together with a knot.

Once this is done its time to locate the Pad Eyes or the attachment location to the kayak. Approx 12″ from tip of bow and stern. Drill the upper hole first and thread the bolt in to hold the pad eye in place. Angle the pad eye away from the bow on a 45 degree angle but make sure it is flat to the boat. Drill the second hole and thread in. Using the washer with the rubber on the inside make sure that faces the inside of the hull. Snug the nut down tight enough where its not going to move. Repeat the same for the stern. Once the pad eyes are installed connect the blocks to each one.

Using the poly reflective rope and run it through the bow block first bottom to top and back to the stern block top to bottom. With the tag end of the rope slide on a piece of heat shrink tubing then loop it through the Nylon ring leaving about 3″ excess crimp two Hog Rings as close to the nylon ring as possible around the tag end and the main line of the poly rope making the loop permanent around the nylon ring. Cut the tag end of the rope back 1/2″ before the Hog Ring. You will now slide the heat shrink tubing over the tag end and the hog rings. Using a heat gun shrink the tubing but take caution not to burn the poly rope nylon ring or heat shrink.

now pull rope from spool end to the nylon ring and add 12″ and cut. Burn end of the rope and run the new tag end through the ring. Snug up the trolley and using 5 half hitches tie the line. Using half hitches will make the trolley adjustable in the future as the rope gets wet it may stretch. Simply un-tie and re-tie snug again.

You have now successfully installed an anchor trolley on your Jackson Cuda 14!

Disclaimer:

Installing hardware may cause damage and/or void manufacturer warranties.  ThePlasticHull.net its authors or any other source of information on this website is in no way responsible for your actions nor any type issues or damage that may occur.  The information provided on this website is a free reference guide only. The authors of all information, sponsors and the owners of the website that host this information are not liable for any problems or issues that arise from the use of this information. Users of this information hereby acknowledge that all use of this information is done by their own free will, at their own sole risk, understanding that destruction of property, injury, or death could occur.