Prior to going out on any event/tournament its a good idea to check the weather forecast prior to packing. This allows you to pack what you will important for the weather instead of packing everything. This time of year it is typically cold nights and cool days so preparing to dress in layers is the best way to go. It appears that this weekend is not going to be very cold but will be a bit windy. Therefor dressing for the wind will be important.
So now that know the type of gear and clothing I will need to bring the next step will be creating a list so forgetting to pack key items is a good idea. Being only 2 nights and a full day and a half of fishing its easy to pack light. All of my fishing tackle and rods are already packed due to previous fishing trips so that cuts out about half of things needed. It is fall so i will need to pack warmer clothing and my semi dry gear. Rule of thumb is water + Air temperature must reach a minimum of 120 degrees or falling into the water could be deadly without the protective dry gear.
I am also looking forward to using my Torqeedo as this is a special place with a 4-5 knot tide at fall new moon. Its going to be ripping and windy. challenge accepted! I will be targeting Striped Bass Blue Fish Speckled Trout and Tautog.
The Jamboree is held in Cape May NJ which is a two hour drive from my home. It is ground zero for some of the best Tautog fishing on the East Coast.
A nice drive south on the Garden State Parkway through the Pine Barens. Looking forward to meeting up with a lot of familiar faces and meeting new anglers! Im also looking forward to doing a little celebrating as today is my birthday!!
Hope to see you all there at the captains meeting tonight!
I have seen this question posted here and there and I have the answer for you! The best way to Mount the Torqeedo 403 Throttle Controller is using a RAM Mount. Then go to your local Hardware store and match the threads to a Stainless Steel screw and mount it to the diamond base RAM ball. Now you have plenty of mounting options!
RAM Mounts you’ll need
RAP-B-201U Composite Double Socket Arm that will receive a 1″ ball
RAM-B-238URAM 2.43″ x 1.31″ Diamond Ball Base with 1″ Ball
Screws needed for ball to controller mounting Metric M4-0.7 x 20mm stainless steel screws
This particular install replaces the Jackson Factory installed Smart Track foot brace steering system. This article explains how to upgrade the steering on the Big Rig utilizing the Sea-lect Designs Toe Pilot foot braces. Using The Toe Pilot system you will simply angle the pedals like you would press a gas or brake pedal on a car to steer the rudder or electric motor. This eliminates the entire track sliding and one knee bent and one straight. Your entire day of fishing will be much more comfortable after this upgrade!
Illustrated in the video this upgrade is a semi advanced install but not an extremely difficult one. This upgrade will also work with the big rig stock Tru-Course rudder. This install conforms to the Torqeedo Ultralight 403 motor steering.
If your big rig does not have a steering kit factory installed Sea-lect Designs does manufacture a full Thru Hull Tru Course Rudder Kit which includes the toe pilot foot braces. The additional part if the install will be running the rudder cable tubing through the kayak.
#10 x 24 1 1/4″ Long Philips head bolt (Hardware Store)
#10 Washer (Hardware Store)
For Torqeedo Setup:
3/16″ Carabeners with eye
Install Instructions:
Removing Existing Smart track System Foot Braces Start with the front bolt. Using a 3/8″ socket with a 1/4″ drive and a Short Philips head screw drive remove the thru hull nut and bolt . Slide the foot brace forward to reveal the rear screw. Now remove the it with a Philips head screw driver. Slide off the back plate and now remove the cable from the foot brace using the 3/8″ socket. Cut the terminal connector from the end of the cable and remove the cable from the stern leaving the tubing in place.
Now you will need to remove the rivet that holds the cable tubing in place as it is int he area of where the new track will be installed. Using a drill bit drill out the center of the rivet until the flange falls off. The back portion of the rivet will fall inside the hull. Patch this hole using a plastic weld or Lexel caulk adhesive.Now using the #10 X 24 – 1 1/4″ bolt and #10 washer dab a drop of thread lock then fasten the left track to the right side of the kayak to the threaded insert. This will allow you to align the track and drill the new front hole. Once the hole is drilled using the #10 x 24 – 1″ bolt washer and nut fasten securely to the kayak. The tracks have to be installed upside down in order to reuse the threaded insert. If you would like to mount the tracks the intended way you will need a rigging bullet as it is impossible to reach the rear area of the track to fasten with a thru bolt.
Now once the track is installed repeat the same steps on the opposite side.
To run the cable.
Run the cable through the cable adjuster first then under the pedal is a hole run through the hole front to back then wrap it around in the groove then through the metal adjuster pulley at the top and then back to the rudder cable tubing which you will then run the cable through to the stern of the kayak. The cable wraps around the toe pilot like an ‘S’ pattern shape.
Once at the stern you will now connect the cable to your factory installed Tru-Course Rudder or in this cast to the Torqeedo steering bracket. Make sure the rudder or motor is centered at the same time the Toe Pilot pedal should be at 90 degrees to the kayak deck. This is to be center for both sides.
Now terminate the end at the cable adjuster by looping the cable through (2) swedges and crimping. Remove the tag end of cable using the diagonal wire cutters. Slide heat shrink tubing over and heat to protect the cut end and the swedges.
Refer to the image above for completed install.
Disclaimer:
Installing hardware may cause damage and/or void manufacturer warranties. ThePlasticHull.net its authors or any other source of information on this website is in no way responsible for your actions nor any type issues or damage that may occur. The information provided on this website is a free reference guide only. The authors of all information, sponsors and the owners of the website that host this information are not liable for any problems or issues that arise from the use of this information. Users of this information hereby acknowledge that all use of this information is done by their own free will, at their own sole risk, understanding that destruction of property, injury, or death could occur.
Prior to going out on any event/tournament its a good idea to check the weather forecast prior to packing. This allows you to pack what you will important for the weather instead of packing everything. This time of year it is typically cold nights and cool days so preparing to dress in layers is the best way to go. It appears that this weekend is not going to be very cold but will be a bit windy. Therefor dressing for the wind will be important.
