KeelEazy is a PVC product manufactured to protect Thermoformed kayak keels. Kilroy LT KeelEazyThe Keel is a part of the kayak that protrudes along the center of the underside of the hull. Thermoform ABS plastic being both strong and thin is actually more abrasive than typical Poly rotomolded kayaks. To extend the life of the kayak and to protect your investment I recommend installing Keel Easy. KeelEazy will protect your kayak against abrasive scuffs, wear and scratches to the keel.

Installing KeelEazy is actually really easy. You can choose to protect the entire keel or just the bow and stern areas which receive the most abuse. KeelEazy comes in seven different colors!

  1. Black
  2. White
  3. Orange
  4. Blue
  5. Green
  6. Red
  7. Yellow

It also comes in different widths however 2″ is the best for most kayak applications.

Install Video:

KeelEazy Installation:

Kilroy LT with KeelEazyI opted to install the Keel Guard on the entire length of the keel. I ordered 14 feet so there would be a little extra just in case. Overall length of the Kilroy LT is 12′-11″.

Step 1: Clean the entire keel area with a clean rag and rubbing alcohol. Let dry. Level off any existing scratches with a razor blade.

Step 2: Round off the beginning edge. (This is not in the video) By folding the edge in half length wise and cutting an arc out it will round off the leading edge for a cleaner look after installation. This is optional.

Step 3: Using a razor blade peel back the protective backing.

Step 4: Place the sticky side down starting 6″ min at the bow. Roll it out and remove the backer keeping the keel guard sticky side down. Keep centered on the keel.

Step 5: Warning: Do not apply too much heat. If you burn the keel guard you will need to replace it with a brand new piece.

Step 6: Using a heat gun slowly heat and mold the keel guard to the bow and the curve in the keel. Using a roller or round tool work out the bends and kinks.

Step 7: Continue using the heat gun in small areas heating up the keel guard and pushing it down. You may want to use a glove because it can get pretty hot.

Step 8: Round off the stern edge.

Step 9: Repeat heat and apply.

Complete!

KeelEazy is available as a Kit or per by the foot from The Kayak Fishing Store.

Disclaimer:

Installing aftermarket products may cause damage and/or void manufacturer warranties.  ThePlasticHull.net its authors or any other source of information on this website is in no way responsible for your actions nor any type issues or damage that may occur.  The information provided on this website is a free reference guide only. The authors of all information, sponsors and the owners of the website that host this information are not liable for any problems or issues that arise from the use of this information. Users of this information hereby acknowledge that all use of this information is done by their own free will, at their own sole risk, understanding that destruction of property, injury, or death could occur.

Sealect Designs sent over an awesome package of rigging hardware for the new Kilroy LT! This hardware will enable the install of the Torqeedo Motor and also leash points for the flush mount rod holders. Look for the installation write up and video in a few weeks!

The package includes the K747205-1 Tru-course Foot Braces for Torqeedo Steering Control, a few different style clam cleats for tie down lines, deck fittings, line rigging hardware, Low Stretch deck line for trim/tie down lines.

Also included new stainless steel cable adjusters! The original ones are aluminum and tend to oxidize in salt water. I will be changing out all of my steering installs with the new ones!

Looking forward to the install!!

 

 

 

 

 

 

 

Unwrapping the Kilroy LT

Picked up my new 2017 Jackson Kayak Kilroy LT Realtree Edition at Delaware Paddlesports today! The Realtree Camo color pattern is amazing. Really pumped to go back to the roots of kayaking ,fishing, hunting, and photographing from a sit in hybrid style kayak. Been looking forward to owning this kayak since Jackson Kayak released it in 2016. Hybrid kayaks are a cross between a canoe and a sit-in kayak. This design makes it easy for one person to paddle like a kayak with the width and open cockpit of a standard canoe.Kilroy Loaded on the F150

Kilroy LT Knowledge:

The Kilroy LT is manufactured using a process called thermoforming using a sheet plastic material or ABS. The process differs from rotomolding as the kayak is molded by heating a thin sheet of ABS plastic then using a vacuum to form the softened plastic to the mold. After cooling the plastic keeps the shape of the mold. The kayak is manufactured in 2 halves then glued together. You can see the seam around the kayak.  This process creates a thinner but strong hull which weighs much less than its polypropylene rotomolded cousins.

Specs and Accessories:

The Kilroy LT is 12 feet 11 inches in length by 33 inches wide and weighs in at 56 pounds. The kayak comes with a “Tech Deck” which mounts to the bow or stern of the cockpit allowing mount points for additional accessories. Also included is the new Jackson Ergo Seat which is the most comfortable yet. Accessories from the factory include two RAM Mount rod holders with track mounts a Naglene water bottle seatback pouch a stand assist strap and long load safety flag. There are 4 yak attack gear tracks for mounting rod holders and camera mounts. The kayak also features a raised deck system which levels out the hull making it easy to stand.

Having yet to paddle the Kilroy LT my paddle selection will be a lightweight Bending Branches Angler Pro 240 – 250 cm in length. Looking forward to the sit in for colder weather paddling with a bit more stability standing due to the deck being closer to the water line. Please do check back on The Plastic Hull for rigging and stories of kayak fishing from the Kilroy LT!

Page 6 of 36« First...45678102030...Last »