Understanding Kayak Rigging – Mounting Base Options

Mounting bases are an essential part of rigging and personalizing your fishing kayak for your needs. A mounting base is typically and after market install for adding mounts for rod holders, fish finders, and other personalized accessory’s.  In this article ThePlasticHull.net covers basic and typical mounting hardware and bases along with track systems.

Fasteners:

There are 4 main types of fasteners typically used for rigging plastic kayaks.  They are as follows.

1. Thru Bolt: (Best Mounting Solution. This includes metal backing plates used in track system mounting.)
2. Rivets: (Second to the best method)
3. Well Nut & Bolt (Typically used with no inside access)
4. Self tapping screw (Has its uses)
5.  Factory molded threaded inserts (Becoming more common. Standard on Jackson fishing Kayaks)

Accessory Bases:

These fastening methods are used to install a mounting base. Depending on the accessory there are choices on base options. For a long time mounting a spline base or a flush mount spline base was the best method of installing rod holders and safety flags. With the evolution of kayak fishing and innovative accessory companies like Ram Mount,s Scotty, and Yak Attack new mounting options have been invented. To cover a few of the main mount base options.

1. Scotty base
2. RAM Ball Base
3. Rail Blaza Deck Mount Base

Gear Tracks:

The most widely used deck mounting solutions in recent time are track mount bases. Track mounting works just like track lighting. Simply by turning the accessory it can be located and secured in any location on the track desired.  I believe Wilderness Systems were the first to incorporate track mount systems into their fishing line of kayaks. Luther Cyphers of Yak Attack developed first the mighty mount which accepted a T style bolt that also is compatible with a track system.  Later he developed the gear track. The gear track really made rigging possibility’s endless. Also created the ability to slide accessory’s to different positions on the fly.  For paddlers the ability to move rod holders out of your paddle sweep on the fly.

In recent time many other fishing kayak manufacturers are incorporating the Yak Attack Gear track or similar track system into their fishing line of kayaks. Along with the tracks came “T Bolt Accessory’s” . The Screw ball was one of the first solutions for mounting accessory’s to the tracks. The ability to have a RAM Mount accessory on a sliding track made options endless. From mounting Rod Holders to Fish finders and camera mounts.

Scotty and RAM Mount spline bases can be adapted to work with track systems by utilizing the Yak Attack MightyMount Post Mount kit. Check it out here!

For 2015 Yak Attack has done it again with a new innovative track system that enables mounting accessory’s from any point on the track. No more sliding from one end to another. Mount between already mounted accessory’s! This is going to make it easy!

For more information on GearTrack Mounting Hardware go to YakAttack.us!

Disclaimer:

Installing hardware may cause damage and/or void manufacturer warranties.  ThePlasticHull.net its authors or any other source of information on this website is in no way responsible for your actions nor any type issues or damage that may occur.  The information provided on this website is a free reference guide only. The authors of all information, sponsors and the owners of the website that host this information are not liable for any problems or issues that arise from the use of this information. Users of this information hereby acknowledge that all use of this information is done by their own free will, at their own sole risk, understanding that destruction of property, injury, or death could occur.

The new Lowrance Elite 5 HDI chart plotter/fish finder’s transducer unfortunately is just too large to be scupper mounted flush on the Cuda. About 1/8″ sticks out on the bottom and i feel this will destroy the transducer over time.

Since this is an HDI unit the transducer needs to be mounted on the exterior of the hull below the waterline. A shoot through hull install with this type of unit will degrade the result of the display. I have two mounting options. One would be the Ram Mounts Transducer flex mount kit. The other being that the Cuda 14 has a removable replaceable skid plate with mounting hardware already molded into the boat. Simply I would have to design a bracket that would mount to the yak via the skid plate and bend up the transom to bolt the transducer through. I think this would eliminate the drag of having a bar and the transducer hanging over the side. Mounted inline with the boats hull it would act as a piece of the hull itself. At least these are my hopes.

Angle Aluminum Stock 1″ x 1/16″ x 36″

I recommend  stainless steel angle but as my choice due to its light weight and non rusting properties in salt water i like to start with aluminum. I also paint it so it is resistant from corroding and pitting. Once the aluminum bracket is fabricated maybe I will make one out of stainless steel. Aluminum is fine due to the trial and error phase of this bracket mount. I am two seasons into my previous scupper mount fabrication where i used aluminum and still see minimal corrosion. The kayak doesn’t sit in the salt water and if its rinsed with fresh water every time it prolongs the life.

Angle alum & Skid Plate

I decided to measure where the bend in the aluminum would be and using a Dremel tool cut of one side off the angle to make it flat.

Bend & Drill to align

I measured the existing skid plate screw holes and drilled appropriately for mounting.

Mounted to Skid Plate for measuring

Once the holes were drilled I mounted the bracket to measure with the transducer the amount of angle needed to mount the skimmer so it was aligned flush with the underside of the hull.

side view mounted to skid plate before cutting

Once i cut the long piece off it looked like this (below)

Transducer Mount after cutting

Transducer Mount after cutting

 Once this was done I aligned the transducer with the bottom of the hull and marked where to drill the hole. Then painted the bracket with black paint to resist the corrosive salt water.

Painted!

Now for mounting!!

Mounted Transducer

Mounted Transducer

Mounted Transducer

Mounted Transducer

Mounted Transducer

Mounted Transducer

Mounted Transducer

Mounted Transducer

Mounted Transducer!

Thats a pretty clean mount! I hope it wil work with loading and unloading the yak on and off my truck. Unfortunatlly it was the best solution but i think it will be fine!

Next will need to run the wiring so i have to figure out how im going to run all of the wire through the hull temporarily for the remainder of the season. These Lowrance wires and plugs are very large and makes the install tough. As in the photos below you can see my existing install using C-Caps. The plug collar is actually larger than the 3/4″ hole drilled here.  I might be temporarily installing through the hatch and then replacing the hatch in the future.  This will give me a chance to hinge the back end of the hatch. At least i can try it once before the final with out worrying about it being pretty..

Existing Hull Pass Through

Existing Hull Pass Through

Disclaimer:

Installing hardware may cause damage and/or void manufacturer warranties.  ThePlasticHull.net its authors or any other source of information on this website is in no way responsible for your actions nor any type issues or damage that may occur.  The information provided on this website is a free reference guide only. The authors of all information, sponsors and the owners of the website that host this information are not liable for any problems or issues that arise from the use of this information. Users of this information hereby acknowledge that all use of this information is done by their own free will, at their own sole risk, understanding that destruction of property, injury, or death could occur.