How To: Upgrade Steering on the Big Rig

This particular install replaces the Jackson Factory installed Smart Track foot brace steering system. This article explains how to upgrade the steering on the Big Rig utilizing the Sea-lect Designs Toe Pilot foot braces. Using The Toe Pilot system you will simply angle the pedals like you would press a gas or brake pedal on a car to steer the rudder or electric motor. This eliminates the entire track sliding and one knee bent and one straight. Your entire day of fishing will be much more comfortable after this upgrade!

Illustrated in the video this upgrade is a semi advanced install but not an extremely difficult one. This upgrade will also work with the big rig stock Tru-Course rudder. This install conforms to the Torqeedo Ultralight 403 motor steering.

If your big rig does not have a steering kit factory installed Sea-lect Designs does manufacture a full Thru Hull Tru Course Rudder Kit which includes the toe pilot foot braces. The additional part if the install will be running the rudder cable tubing through the kayak.

Video of the install!

This article is the install breakdown and How To.

Tools Needed for full install:

• 3/8″ socket
• 1/4″ Ratchet
• 3/8″ Open end box wrench
• Short Philips head screwdriver
• Hex Key Set
• Pry Tool
• Drill
• Drill Bits
• Diagonal Wire Cutters
• Needle Nose Pliers
• Heat Gun
• Razor Blade

Parts & Materials Needed:

• Sea-Lect Designs Toe Pilot Foot Braces K747205-1
• Sea-Lect Designs Cable Adjusters K747260-1
• 30 feet of stainless steel rudder cable
• Heat Shrink Tubing
• 8 Swedges or Cable Crimps
• Lexel or Marine Goop
• 2 9″ Lengths of 3/16″ Bungee Chord
• #10 x 24 1 1/4″ Long Philips head bolt (Hardware Store)
• #10 Washer (Hardware Store)

For Torqeedo Setup:

• 3/16″ Carabeners with eye

Install Instructions:

Removing Existing Smart track System Foot Braces Start with the front bolt. Using a 3/8″ socket with a 1/4″ drive and a Short Philips head screw drive remove the thru hull nut and bolt . Slide the foot brace forward to reveal the rear screw. Now remove the it with a Philips head screw driver. Slide off the back plate and now remove the cable from the foot brace using the 3/8″ socket. Cut the terminal connector from the end of the cable and remove the cable from the stern leaving the tubing in place.

Now you will need to remove the rivet that holds the cable tubing in place as it is int he area of where the new track will be installed. Using a drill bit drill out the center of the rivet until the flange falls off. The back portion of the rivet will fall inside the hull. Patch this hole using a plastic weld or Lexel caulk adhesive.Now using the #10 X 24 – 1 1/4″ bolt and #10 washer dab a drop of thread lock then fasten the left track to the right side of the kayak to the threaded insert. This will allow you to align the track and drill the new front hole. Once the hole is drilled using the #10 x 24 – 1″ bolt washer and nut fasten securely to the kayak.  The tracks have to be installed upside down in order to reuse the threaded insert. If you would like to mount the tracks the intended way you will need a rigging bullet as it is impossible to reach the rear area of the track to fasten with a thru bolt.

Now once the track is installed repeat the same steps on  the opposite side.

To run the cable.

Run the cable through the cable adjuster first then under the pedal is a hole run through the hole front to back then wrap it around in the groove then through the metal adjuster pulley at the top and then back to the rudder cable tubing which you will then run the cable through to the stern of the kayak. The cable wraps around the toe pilot like an ‘S’ pattern shape.

Once at the stern you will now connect the cable to your factory installed Tru-Course Rudder or in this cast to the Torqeedo steering bracket. Make sure the rudder or motor is centered at the same time the Toe Pilot pedal should be at 90 degrees to the kayak deck. This is to be center for both sides.

Now terminate the end at the cable adjuster by looping the cable through (2) swedges and crimping. Remove the tag end of cable using the diagonal wire cutters. Slide heat shrink tubing over and heat to protect the cut end and the swedges.

Refer to the image above for completed install.

Disclaimer:

Installing hardware may cause damage and/or void manufacturer warranties.  ThePlasticHull.net its authors or any other source of information on this website is in no way responsible for your actions nor any type issues or damage that may occur.  The information provided on this website is a free reference guide only. The authors of all information, sponsors and the owners of the website that host this information are not liable for any problems or issues that arise from the use of this information. Users of this information hereby acknowledge that all use of this information is done by their own free will, at their own sole risk, understanding that destruction of property, injury, or death could occur.

Image from http://blackdiamondequipment.com/

Over the years of night fishing and early morning to day fishing I have used many different headlamps. Only one has stood out beyond the rest. The Black Diamond Storm!! The storm was created for outdoor enthusiasts mainly for hiking and camping. I feel being in a marine environment was the ultimate test. There are a few musts within a headlamp needed for kayak fishing.

1. Must be waterproof
2. Must be bright
3. Must be operable with one hand
4. Push Button On Off Operation
5. Must fit head snugly
6. Has to be light and comfortable to wear
7. Needs Red light options
8. LED is BEST
9. Good Battery Life

Previous headlamps were not waterproof. Some died just from being rained on. Others well the salt eventually corroded the insides. I have owned filament light bulb flash light style and LED styles the LED is the best.  LED is much brighter than the standard filament light bulbs.  The diode also lasts longer. Some were turned on by turning the lens others were push button. The push button is much better for 1 hand operation.

After 5 or six different headlamps I had a coupon for a local Eastern Mountain Sports store. I went in just to use the coupon on someting kayak fishing related but wasn’t sure on what. Once in the store looking around i came upon the Black Diamond headlamp display. Realizing my current headlamp had just died the morning prior I became very interested. Looking at the package it stated the headlamp was indeed waterproof. Now almost sold reading more about the features it has a RED lamp option and 2 bright light options.  One being 2 white single power LED’s which give a good general flood of light for doing most tasks and a bright “Quad Power LED” in the center . The Quad Power is very bright and acts like a spot lite. It shines for a range of 70 m or about 230 feet. The brightness is perfect for tieing knots and de-hooking fish.  The single power led’s light is a max of about 7 m or 23 feet which is good for general tasks and saves battery life. All lighting modes are switched using a single button. Holding the button down dims the light levels (in older models). Pressing the button quickly will go from on to strobe and pressing slowly will switch the light modes.

New models have a function called power tap technology. Simply by tapping the side of the headlamp the brightness levels will go up or down within preset intervals.

The storm also has a waterproof rating of IPX7 which is water tight 30 meters below water for 30 mins. This was a key feature for myself as a kayak angler. Another great feature is the included power meter which will show green yellow and red for status of battery life when the light is turned on. The weight of the entire headlamp is minimal at 3.9 oz making it comfortable to wear all night long. The MSRP of the headlamp is $50.00 and well worth the price. The current one i have has lasted 3 years so far. If you do not use the headlamp very often do take the batteries out as they may leak over time damaging the inside of the light.

For more information on the Black Diamond Storm Headlamp check out the Black Diamond Website here!

Smith Optics Dolan Style Sunglasses

As we all know sunglasses are an essential need for our on the water experience. Protecting your eyes and dampening glare to enhance our vision. For years the use of cheap $20.00 polarized sunglasses was the way I rolled. Stating they are cheap and it doesn’t hurt if they get lost scratched or damaged. Until I purchased a pair of Smith Optics Sunglasses with the patented Chromapop Lenses. Wow did it change my world. The crystal clarity the incredible colors and the great polarized ability to see deeper into the water. Even driving is more pleasant.

The sunglasses are light weight and extremely comfortable thanks to the dual spring hinge design. The arms contour to your head and hold tight to your head but not to tight.  The lenses are coated with both a hydrleophobic and Anti-Glare coatings. The hydrleophobic acts like a barrier that repels water and makes salt and finger prints wipe easily. The anti-glare is applied to the back of the lens to eliminate glares that may reflect from side light.

I have been wearing Smith Optic sunglasses this entire fishing season and would recommend a pair for every angler! There’s no way to go back to cheap sunglasses after experiencing such quality craftsmanship and visual bliss!

Smith Optics Dockside

 Pros:

• Light weight
• Spring arms for contouring to your head for best fit.
• Included Hard Case
• Micro Fiber Cloth Bag
• Lenses wick water away and are easy to clean.
• Brilliant clarity
• Polarized

Cons:

None

MSRP of frames and lenses mentioned is 200.00 +

Visit www.SmithOptics.com for more information